Like what you see? Get in Touch

INSTALLATION METHOD

Click here to view [ Step by Step Instructions ]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP - BY STEP INSTALLATION

STEP 1: INSTALLATION TOOLS PREPARATION

步骤1:准备工具

a) Sticking Tools :
i) DUNLOP / MAXBOND Multipurpose Adhesive   多功能粘合剂  &  Putty Spreader  填缝剂小刀
ii) 3M SCOTCH / NISSHO ACRYLIC Double sided Tape  双面胶
b) Painting Tools:
i) Wall Paint  油漆
ii) Painting Brush  油漆刷 / Painting Roller (4 inch)  4寸滚轮油刷
c) Gaps Filling Tools (If  necessary) :
i) Joint Compound / Paintable caulking  填缝剂                                                    
ii) Sand Paper (180 – 240)  砂纸 (180-240)
d) Helping Tools :
i) Pencil  铅笔
ii) Measuring Tape  尺带
iii) Level Meter  水平仪
iv) Utility Knife  手工刀


STEP 2: WALL SURFACE PREPARATION

步骤2:墙面准备

Wipe the wall and make sure the wall surface is clean, dry and free of debris. Plan your wall’s layout accordingly whether to install the panels from side to side, top to bottom, or from center out. Measure the wall and draw marked lines according to the panel size.

清理墙面以确保墙面清洁,干燥,无碎片。计划墙面的设计,根据您所选择的3D BOARD尺寸,测量以及画标线。安装3D BOARD方式可以从边缘至另一边缘,从上至下或左至右,或从中心点向外安装。



STEP 3: 3D BOARD PANELS PREPARATION (IF NECESSARY) 
步骤3:3D BOARD准备(如果有必要)

If necessary for you to install panels on the area at the corner which the area is less than the panel size, measure the total size of the area, mark the total size on the back surface of panel with a pencil, then cut it with utility knife / penknife. Sand the cutting edge of the panels.

如果需要安装位于角落的剩余墙面面积小于3D BOARD产品本身的尺寸,请测量剩余墙面面积尺寸,然后依照该尺寸用铅笔标记于3D BOARD产品背面,接着用手工刀依照标记进行切割。将切割边缘用砂纸磨平。



STEP 4: USING A PERMENANT ADHESIVE

步骤4:使用多功能粘合剂

Please refer to installation tools preparation 1(a)

To paste the panels on the wall, you might use multi-functional glue or double sided tape. After applying a thin layer of  adhesive onto the wall and on the back surface of the panels, leave it for few seconds till the adhesive appearing in half dry condition, then paste the panel on the wall according to the marked line in Step 2. If you are using double sided tape, applying it at the surrounding of the board. Peal off the double sided tape plastic cover then paste it on the wall.

请参考1(a)的工具准备。 

进行产品粘贴步骤时,您可以使用多功能粘合剂或双面胶。首先先于3D BOARD产品背面以及墙面涂上适量粘合剂,直到粘合剂呈现半干燥的情况,然后根据步骤2的标线将产品粘贴于墙面上。如果您使用双面胶带,那就把双面胶贴在3D BOARD的周围。接着把塑胶贴纸撕下来然后把3D BOARD粘上墙壁。

 

STEP 5(a): PLACING THE PANELS ON THE WALL – Installation WITH Joint Seams

步骤5(a):产品粘贴步骤 – 间隔式安装

For D.I.Y, we recommend this installation with joint seams –leaving some gaps between the panels, the size of the gaps is depends on own favourite.

我们推荐D.I.Y的顾客采用间隔式安装方式 – 即在每片3D BOARD产品之间预留些缝隙,缝隙大小由个人喜好而定。

Repeat with step 4 for each units of the panels until the installation job finish. Remember to apply some force on each panels specially the corner part so that it could attach to the wall tightly. Use a damp cloth to clean the excess adhesive.

重复步骤4,直到完成每片3D BOARD产品的粘贴安装。粘贴时请注意在每片产品上施于些许力量,尤其是角落四周围,以便产品可稳固粘贴于墙面上。使用湿布清洁产品周围多余的粘合剂。

 

STEP 5(b): PLACING THE PANELS ON THE WALL – Installation WITHOUT Joint Seams

步骤5(b):产品粘贴步骤 – 无缝隙式安装

 

If you plan to touch up the seams using joint compound on later stage, make sure all panels are placing close to one another.

如果您打算在接下来的步骤使用填缝剂以减少缝隙,请在粘贴步骤时确保每片3D BOARD产品都相互紧贴。

Repeat with step 4 for each units of the panels until the installation job finish. Remember to apply some force on each panels especially the corner part so that it could attach to the wall tightly. Use a damp cloth to clean the excess adhesive.

重复步骤4,直到完成每片3D BOARD产品的粘贴安装。粘贴时请注意在每片产品上施于些许力量,尤其是角落四周围,以便产品可稳固粘贴于墙面上。使用湿布清洁产品周围多余的粘合剂。


 

STEP 6: FILLING THE SEAMS (Only for Installation WITHOUT Joint Seams STEP 5(b))

步骤6:缝隙填补步骤 (只需用于无缝隙式安装步骤5(b))

A modular product will have seams. If you wish to minimize the seams, you could apply putty filler / paintable joint compound / paintable caulk to fill up the seams.

任何模块产品都会有接缝。如果你打算减少缝隙,您可以使用填缝剂。

Before applying the joint compound, a layer of premier sealer is recommended to be applied to seal the 3D BOARD surface. After applying and when the filling material dry out, sand the seams with sand paper to make it smooth. Then, apply another layer of undercoat sealer paint before painting to get the best result.

我们建议您在使用填缝剂前先上一层底漆。然后在缝隙上填上填缝剂。等至填缝剂干透后,使用砂纸将缝隙磨平。接着,再涂上一层底漆以达到最佳效果。



 

STEP 7: PAINTING

步骤7:产品上漆步骤

The panels are now ready to be painted. 3D BOARD suits to any types of  paint available in the market. The panels could be brushed, rolled, or sprayed with various types of paint. Painting a completed 3D BOARD wall is the same as painting drywall.

完成粘贴步骤的3D BOARD现在已可准备上漆。任何市面上的油漆类型都适用于3D BOARD上。您可随意进行粉刷,滚刷,或是喷漆上色。在3D BOARD表面上漆,就像平常于普通墙面上漆一样简单容易。